Difference between revisions of "Lulzbot AO-100"
From Hackerspace.gr
m |
Thanos.Husk (Talk | contribs) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 22: | Line 22: | ||
# Load .stl in slic3r. | # Load .stl in slic3r. | ||
# Check configuration and generate Gcode file | # Check configuration and generate Gcode file | ||
| − | # Plug in AO-100 to power and USB port of your computer and power it on. | + | # Direct print (non octopi) |
| − | # Open Printrun and connect to tty port of the AO-100 (through USB) | + | ## Plug in AO-100 to power and USB port of your computer and power it on. |
| − | # Home X-Y-Z axis by pressing the home buttons (corners) for all axis. | + | ## Open Printrun and connect to tty port of the AO-100 (through USB) |
| + | ## Home X-Y-Z axis by pressing the home buttons (corners) for all axis. | ||
# Set temperatures for extrusion in the left. Extrusion 227-230 for ABS and 200 for PLA (to be tested). Bed temperature 100 degrees. Press set on both to heat them up and check the watch checkbox. | # Set temperatures for extrusion in the left. Extrusion 227-230 for ABS and 200 for PLA (to be tested). Bed temperature 100 degrees. Press set on both to heat them up and check the watch checkbox. | ||
# Wait for temperatures to be reached. | # Wait for temperatures to be reached. | ||
| Line 37: | Line 38: | ||
== Current setup == | == Current setup == | ||
| − | * '''Extrusion head''': 0. | + | * '''Extrusion head''': 0.4mm (0.25 and 0.35 are also available) |
| − | * '''Filament''': 3mm | + | * '''Filament''': 3mm ABS (printer can also take 1.25mm) |
= Todo = | = Todo = | ||
Latest revision as of 15:47, 3 January 2022
Contents
Intro
Acquiring
Aleph Objects (the makers of Lulzbot) run a giveaway for hackerspaces and hackerspace.gr was one of the 8 winners! Late June 2013 the AO-100 was in our space. Thanks Aleph Objects!
Printer
Our printer is a standard issue pre-assembled AO-100
How to print
There are many cam and printing software that might work for you. The recommended stack is using the following programs:
Process
The process to print something can be quickly outline as such:
- Obtain .stl file of model. This can be either found directly (from sites like thingiverse) or designed with Blender, OpenSCAD etc.
- Start slic3r and load conf file (see below)
- Load .stl in slic3r.
- Check configuration and generate Gcode file
- Direct print (non octopi)
- Plug in AO-100 to power and USB port of your computer and power it on.
- Open Printrun and connect to tty port of the AO-100 (through USB)
- Home X-Y-Z axis by pressing the home buttons (corners) for all axis.
- Set temperatures for extrusion in the left. Extrusion 227-230 for ABS and 200 for PLA (to be tested). Bed temperature 100 degrees. Press set on both to heat them up and check the watch checkbox.
- Wait for temperatures to be reached.
- Load Gcode file and press "print".
- Experience awesomeness!
Calibration
Calibration of Z axis may be required from time to time. Check manual for now or ask Manthos or Pierros.
Configurations
Stock settings for slic3r can be found here.
Current setup
- Extrusion head: 0.4mm (0.25 and 0.35 are also available)
- Filament: 3mm ABS (printer can also take 1.25mm)
Todo
- Upgrade to AO-101 (see upgrade post)
